manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

52

Section 4: System Control and Debug Unit

 Document

1250_1125-UM100CB-R

The main interrupt registers are all 64 bits wide: 

Table 21:  Interrupt Registers

Name

Description

interrupt_diag

_0

 - 00_1002_0010

_1

 - 00_1002_2010

Setting a bit in this register raises the corresponding interrupt. Software must clear the bit 
to remove the interrupt. This register is intended for diagnostics only.

interrupt_ldt_set

 

00_1002_0048

This write only register is written with a HyperTransport interrupt message and will decode 
it into setting a single bit in either the interrupt_ldt or mailbox register, and thus an interrupt 
will be raised.

interrupt_ldt

_0

 - 00_1002_0018

_1

 - 00_1002_2018

The HyperTransport interrupt controller will set the bit corresponding to the interrupt vector 
number for vectors in the range 0-63. The CPU can read this register to find which 
HyperTransport interrupts have been posted. 

interrupt_ldt_clr

_0

 - 00_1002_0020

_1

 - 00_1002_2020

This is not a register. Writing a one to a bit in this location clears the corresponding bit in 
the interrupt_ldt register.

interrupt_mask

_0

 - 00_1002_0028

_1

 - 00_1002_2028

Setting a bit in this register masks the corresponding interrupt. All bits in this register are 
set at reset, masking out all interrupts.

interrupt_status_n

 n=0-7

_0

 - 00_1002_0100..138

_1

 - 00_1002_2100..138

Read Only. There is a status register for each of the outputs from the mapper. A bit will be 
set only if the corresponding source is interrupting, is not masked and is mapped to this 
output. 

interrupt_source_status

_0

 - 00_1002_0040

_1

 - 00_1002_2040

Read Only. A bit will be set if the corresponding source is interrupting regardless of the 
state of the interrupt mask. 

interrupt_trace

_0

 - 00_1002_0038

_1

 - 00_1002_2038

Setting a bit in this register allows the interrupt to trigger the trace unit.

interrupt_map0

...

interrupt_map63

_0

 - 00_1002_0200..3F8

_1

 - 00_1002_2200..3F8

There are 64 interrupt mapper registers. Each is 3 bits wide and encodes the mapping 
from the interrupt number given in 

Table 22

 onto the CPU interrupt lines as described in 

Table 18

.

Table 22:  Interrupt Sources

Number

Name

Description

Method to clear

0

watchdog_timer_int_0 

Watchdog timer 0 timeout

Interrupt is raised on first timeout of the timer (the 
second will reset the machine). It is cleared by writing 
to the timer configuration register. See 

Section: “Watchdog Timers” on page 57

.

1

watchdog_timer_int_1 

Watchdog timer 1 timeout 

Interrupt is raised on first timeout of the timer (the 
second will reset the machine). It is cleared by writing 
to the timer configuration register. See 

Section: “Watchdog Timers” on page 57

.

2

timer_int_0 

General timer 0 

Interrupts when timer reaches zero, cleared by a write 
to the timer configuration register. See 

Section: “General Timers” on page 58

.

3

timer_int_1 

General timer 1 

Interrupts when timer reaches zero, cleared by a write 
to the timer configuration register. See 

Section: “General Timers” on page 58

.

4

timer_int_2 

General timer 2 

Interrupts when timer reaches zero, cleared by a write 
to the timer configuration register. See 

Section: “General Timers” on page 58

.

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Бренд: Paradyne Страницы: 2
Ratoc Systems SCSI PC Card REX-9530V Product Manual preview
SCSI PC Card REX-9530V
Бренд: Ratoc Systems Страницы: 30
Idis DR-8432 Installation Manual preview
DR-8432
Бренд: Idis Страницы: 31
Roland MSL-15 Owner'S Manual preview
MSL-15
Бренд: Roland Страницы: 12
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Бренд: LogLogic Страницы: 30
MF DIGITAL DIRECTOR PRO series Operator'S Manual preview
DIRECTOR PRO series
Бренд: MF DIGITAL Страницы: 79
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Бренд: Supero Страницы: 16
QTech QSW-2900 User Manual preview
QSW-2900
Бренд: QTech Страницы: 406
Omron NJ501-1300 User Manual preview
NJ501-1300
Бренд: Omron Страницы: 432
AXIOMTEK UST510-52B-FL Series User Manual preview
UST510-52B-FL Series
Бренд: AXIOMTEK Страницы: 77
Lanner NCA-6520 User Manual preview
NCA-6520
Бренд: Lanner Страницы: 141
ALIBI ALI-NVR71128R User Manual preview
ALI-NVR71128R
Бренд: ALIBI Страницы: 232
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Бренд: Microchip Technology Страницы: 41
Quatech SSPX-100 User Manual preview
SSPX-100
Бренд: Quatech Страницы: 5
Abus TVAC21000 User Manual preview
TVAC21000
Бренд: Abus Страницы: 98
Intel Core 2 Duo E4300 Design Manual preview
Core 2 Duo E4300
Бренд: Intel Страницы: 55
LevelOne ServCon FPS-3003 Quick Install Manual preview
ServCon FPS-3003
Бренд: LevelOne Страницы: 45
Commax CVN-0430F User Manual preview
CVN-0430F
Бренд: Commax Страницы: 122

Бренды по названию

Популярные бренды

Загрузить еще бренды