background image

Setup

Note:

Determine the left and right sides of the

machine from the normal operating position.

Installing the Plow Control
Joystick

Secure the plow control joystick to the handle link
(

Figure 3

).

g298628

Figure 3

1.

Joystick

3.

Handle link

2.

Nut (3/8 inch)

Checking the Tire Pressure

Pressure: 124 kPa (18 psi)

Check the air pressure in the tires.

g001055

Figure 4

Checking the Engine-Oil
Level

Before you start the engine and use the machine,
check the oil level in the engine crankcase; refer to

Checking the Engine-Oil Level (page 29)

.

Adding Fuel to the Machine

Add fuel to the machine before starting it; refer to

Adding Fuel (page 13)

.

Note:

Ensure that the fuel-shutoff valve is open

before attempting to start the engine.

Checking the
Hydraulic-Fluid Level

Before you start the engine and use the machine,
check the hydraulic-fluid level in the tank; refer to

Checking the Hydraulic Fluid (page 37)

.

Connecting the Battery
Cables

Connect the positive terminal first and negative last.

g294507

Figure 5

1.

Negative (black)

2.

Positive (red)

7

 

Содержание Snowrator SNR24001

















































Отзывы: