Bosch Singular 4000 Скачать руководство пользователя страница 62

Страница: 62 / 68

6 2

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

9.18 Heat Exchanger

WARNING: FIRE, EXPLOSION, PERSONAL INJURY



Prior to performing any work on the boiler, ensure the gas
supply is turned off and power unplugged .

1. Refer to 9.1 Preparation Step.

2. Drain the water using the drain valve and water ﬁ lter (Item 1).

Figure 118

3. The Heat Exchanger and Turbo Fan will come out as one complete unit.

However, if there is not space to remove all together, separate the fan from
the heat exchanger according to Section 9.16.

4. Loosen ﬁ xing screw on bottom right hand side of heat exchanger cover

and Remove heat exchanger cover and disconnect ﬂ ame rod and electrode
assembly wires (Fig.120, Item 2).

Figure 119

5. See Figure 121. Separate the fan connection terminal (Item 1), solenoid

valve terminal (Item 2), overheat prevention device wire (Item 3), and heat
exchanger temperature sensor (Item 4).

Figure 120

6. Separate the gas pipe (Item 1)using a wrench.

Figure 121

7. Loosen 2 screws and remove ignition transformer (Fig.123, Item 1) and save

for reinstallation.

8. Unclip exhaust sensor connector (Fig.123, Item 2).

Figure 122

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 62 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: