Bosch Singular 4000 Скачать руководство пользователя страница 41

Страница: 41 / 68

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

AE Error - Wire Check

1. Check the connection of the air pressure switch and the wire.

Figure 51

Control Board

Figure 52

Air Pressure Switch Wire

AE Error - Air Pressure Switch Check

1. Check the air pressure switch for abnormalities under combustion stop

condition.

—

Normal: under 1Ω

—

Abnormal: O.L

Figure 53

2. Operate the water heater using hot water over 4GPM and check the air

pressure switch for abnormalities when the fan spins at the maximum speed.

—

Normal: 0.L

—

Abnormal: under 1Ω

3. Replace the air pressure switch if the resistance is abnormal.

AE Error - Foreign Material Check

1. Check for any restrictions or blockage in the venting system.

—

Remove foreign material if present.

AE Error - Control Board Check

1. Replace the control board if the connection of air pressure switch and the

resistance are normal and no foreign material is present in the air inlet and
outlet.

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 41 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: