Bosch Singular 4000 Скачать руководство пользователя страница 59

Страница: 59 / 68

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

9.14 Touch pad

1. Refer to 9.1 Preparation Step.

2. Separate the touch pad from the touch pad bracket by pushing it up (Item 1).

Figure 104

Figure 105

3. Disconnect the touch pad connection terminal (Item 2). Connect the new

touch pad to the connection terminal. Insert touch pad into the 4 grooves
(Item 3) marked on the ﬁ gure below and push down.

Figure 106

9.15 Condensation Trap

1. Refer to 9.1 Preparation Step.

2. Drain the water using the drain valve and water ﬁ lter (Item 2).

Figure 107

3. Disconnect the wire from the condensation trap (Item 2).

4. Separate the condensation trap hose by lowering the clip (Item 3).

Figure 108

5. Loosen the condensation trap cap (Item 4). (Counterclockwise)

6. Loosen the 4 ﬁ xing screws at the bottom of the chassis (Item 5).

Figure 109

7. Replace with a new condensation trap.

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 59 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: