Bosch Singular 4000 Скачать руководство пользователя страница 20

Страница: 20 / 68

2 0

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

A2 Error - Wire Check

1. Check the connection of the Fan Connector Wire (Red-Black).

2. Check the connection of the Hall IC Connector Wire (Yellow-White).

Figure 6

Fan

Connector

Wire

Hall IC

Connector

Wire

3. Check the connection of the control board Connector Wire (Red-Black).

Figure 7

Control

Board

Connector

A2 Error - Control board Input Voltage Check

1. Measure the control board input voltage (measure while using the hot water)



Multi tester range: “DC V”

Measurement Method

Measured value

Measure the applied voltage

Red - Black: DC 5 – 45 V

Yellow – Black: DC 10 – 13 V

Measure FAN Hz

White – Yellow: 0 – 270 Hz

Table 24

Figure 8

Applied Voltage Measurement Method

Figure 9

FAN Hz Measurement Method

2. If the voltage is measured normally but the fan does not operate, replace the

fan.

3. If the fan operates but Hz cannot be measured, replace the fan.

4. If the voltage cannot be measured, replace the control board.

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 20 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: