Bosch Singular 4000 Скачать руководство пользователя страница 58

Страница: 58 / 68

5 8

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

9.12 Electrode Assembly

1. Refer to 9.1 Preparation Step.

2. Separate the electrode assembly connection terminal (Item 1).

3. Separate the electrode assembly cap (Item 2).

4. Loosen the 2 ﬁ xing screws (Item 3).

Figure 100

5. Replace with a new electrode.

6. When replacing the electrode assembly, use the new gasket and bracket

that are provided with the new part. Assemble in the order of gasket (1),
electrode assembly (2) and bracket (3) as shown in the ﬁ gure below.

Figure 101

9.13 Flame Rod

1. Refer to 9.1 Preparation Step.

2. Separate the ﬂ ame rod connection terminal.(Item 1).

3. Separate the ﬂ ame rod cap. (Item 2).

4. Loosen the 3 ﬁ xing screws. (Item 3).

Figure 102

5. Replace with a new ﬂ ame rod.

6. When replacing the ﬂ ame rod, use the new gasket and bracket that are

provided with the new part.

7. Assemble in the order of gasket (1), ﬂ ame rod (2), and bracket (3) as shown

in the ﬁ gure below. Remove the brown tape part (4) from the gasket and
attach it to the bracket. (Do not attach it to the sensible heat exchanger. )

Figure 103

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 58 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: