Bosch Singular 4000 Скачать руководство пользователя страница 17

Страница: 17 / 68

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

7.14 Burner

Part No.

7738007256*

Function

Combustion with a mixture of gas and air.

Failure Event



Unable to initialize/sustain combustion.



Foreign substance or soot deposit on the burner surface.



Gas leakage from the burners.

Effects



Unexpected combustion.



Unstable flame condition and flame lifting.



Ignition failure.



Excess carbon monoxide emissions.

Error Code

Diagnostic

Visual inspection: Excess foreign substance on the burner surface and

unstable ﬂ ame condition during combustion.

Color/Number of Wires

N/A

Table 17

* included in heat exchanger assembly

7.15 Gas Valve

Part No.

7738007270

Function



Provide the gas for combustion.



For some reason, it shuts off the gas valve automatically and prevents
an unsafe condition due to combustion .

Failure Event



Gas leak from the valve.



Unable to open/close.

Effects



Gas leak from the unit.



The unit does not operate.

Error Code

A6, A8

Diagnostic



Visual inspection: Disconnection or breakage of wires.



Check range of voltage shown below.

Color/Number of Wires

White-White: DC 120 V

Table 18

7.16 Touch Pad

Part No.

7738007238

Function

Turn the boiler on or oﬀ , adjust the water temperature, and change the
modes.

Failure Event

Malfunction of Touch Pad

Effects

No operation of unit.

Error Code

Diagnostic



Visual inspection: Connection or breakage of wires.



Voltage check: Check range of voltage shown below.

Color/Number of Wires

Yellow-Yellow: DC 24 V

Table 19

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 17 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: