manualshive.com logo in svg

Bosch Singular 4000, Руководство по обслуживанию, Страница: 18 / 68

Поделиться
Скачать
Bosch Singular 4000 Скачать руководство пользователя страница 18

1 8

 |

 

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

7.17     Control Board

Part No.

7738007249 (Singular 5200)

7738007248 (Singular 4000)

Function

To control each component and performance of unit.

Failure Event

 

Malfunction of control board.

 

Unit does not operate.

Effects

 

A component does not operate within the unit.

 

In case of the control board failure, the water heater does not 

operate.

Error Code

—

Diagnostic

Visual inspection: Connection or breakage of water or burn marks on the 
control board.

Color/Number of Wires

N/A

Table 20

7.18     Condensate Trap Assembly

Part No.

7738007273

Function

Drain condensation, which is created while combusting.

Failure Event

 

Fail to drain condensation caused by clogged trap.

 

Condensation leakage into the unit.

Effects

 

Stop combustion.

 

Condensation leakage.

Error Code

AD

Diagnostic

 

Visual inspection: Connection or breakage of wires, check for 

physical damage to the trap body.

 

Voltage Check: Check range of voltage shown below.

Color/Number of Wires

Green-Red: AC 24 V

Table 21

7.19     Air Pressure Switch

Part No.

7738007247 (Singular 5200)

7738007246 (Singular 4000)

Function

Prevents operation of the unit due to unsafe condition. Back pressure or 

blockage has occurred in the exhaust vent.

Failure Event

No operation of the unit.

Effects

 

Stop combustion.

 

No operation of the unit.

Error Code

AE

Diagnostic

 

Visual inspection: Connection or breakage of wires.

 

Voltage check: Check range of voltage shown below.

Color/Number of Wires

Green-Green: DC 5 V

Table 22

Содержание Singular 4000





































































Отзывы:

Нет отзывов