Bosch Singular 4000 Скачать руководство пользователя страница 42

Страница: 42 / 68

4 2

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

8.14 EO Error (Abnormal Operation: Outdoor Temperature Sensor)

Error

Description

Outdoor Temperature Sensor Error

Error is displayed when the ambient sensor has short-circuited or is disconnected

Checkpoint



Check if the outdoor temperature sensor wire is connected correctly.

1. Control board wire
2. Outdoor temperature sensor wire



Measure and check the resistance of the outdoor temperature sensor wire (NTC method).



Check the outdoor temperature sensor for disconnection



Check the outdoor temperature sensor for short-circuit

Table 34

Figure 54

Check the assembly

condition of the control board

and the temperature sensor wire

Reassemble the control board

and the temperature sensor wire

Replace the temperature

sensor

Replace the temperature

sensor

Replace the control board

Check the

temperature

sensor for short

Is the

resistance of the

temperature sensor

normal?

Yes

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 42 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: