Bosch Singular 4000 Скачать руководство пользователя страница 55

Страница: 55 / 68

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

9.2 Control Board

1. Refer to 9.1 Preparation Step.

2. Loosen the connection terminals in the control board.

3. Loosen the 3 control board ﬁ xing screws (circled in blue) assembled to the

chassis (Fig. 88).

Figure 88

4. Replace with a new control board and tighten the connection terminals.

5. Tighten the 3 control board ﬁ xing screws. (Tighten the ground wire with the

control board top screw together.)

9.3 Sensor, Heating/Return

1. Refer to 9.1 Preparation Step.

2. Disconnect the temperature sensor terminal.

3. Replace with a new temperature sensor.

Figure 89

9.4 Sensor, DHW

1. Refer to 9.1 Preparation Step.

2. Disconnect the temperature sensor terminal.

3. Replace with a new temperature sensor.

Figure 90

9.5 Exhaust Temperature Sensor_T4 (Blue)

1. Refer to 9.1 Preparation Step.

2. Disconnect the temperature sensor terminal (Item 1).

3. Loosen the screw and remove the temperature sensor (Item 2).

Figure 91

4. Replace with a new temperature sensor and tighten the screw.

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 55 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: