Bosch Singular 4000 Скачать руководство пользователя страница 3

Страница: 3 / 68

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

Table of Contents

1 Key to Symbols and Safety Instructions

1.1 Key to Symbols

1.2 Safety

2 Key Components

3 Technical Data

4 Dimensions

5 Setting the DIP Switches

6 Wiring Diagram

7 Key Components Description

7.1 Pump

7.2 Turn Down Ratio (TDR) Solenoid valve

7.3 Oriﬁ ce

7.4 Fan

7.6 High Limit Cutout HEX T2 (302°F)

7.7 High Limit Cutout Supply T3 (203°F)

7.8 Primary Heat Exchanger

7.9 Secondary Heat Exchanger

7.10 Sensor

7.11 Electrode

7.12 Flame Rod

7.13 Ignition Transformer & Wire

7.14 Burner

7.15 Gas Valve

7.16 Touch Pad

7.17 Control Board

7.18 Condensate Trap Assembly

7.19 Air Pressure Switch

8 Troubleshooting

8.1 A2 Error (Abnormal Operation: Fan)

8.2 A3 Error (Abnormal Operation: Pump)

8.3 A4 Error (Overheating of Heat Exchanger)

8.4 A5 Error (Low Water Pressure)

8.5 A6 Error (Ignition Error)

8.6 A7 Error (Abnormal Operation: Gas Valve Relay)

8.7 A8 Error (Abnormal Operation: Gas Valve)

8.8 A9 Error (Exhaust Temperature Sensor Error)

8.9 AA Error (Overheating)

8.10 AB Error (Abnormal Operation: Heat Exchanger Temperature Sensor

8.11 AC Error (Abnormal Operation: DHW Sensor)

8.12 AD Error (Clog of Condensate Trap)

8.13 AE Error (Blockage of Flue Pipe)

8.14 EO Error (Abnormal Operation: Outdoor Temperature Sensor)

8.15 E1 Error (Abnormal Operation: Exhaust Temperature Sensor)

8.16 E2 Error (Exhaust Temperature Overheating)

8.17 E3 Error (Abnormal Operation: Return Sensor)

8.18 E4 Error (Abnormal Operation: Pressure Sensor)

8.19 E7 Error (Abnormal Operation: Gas Valve Relay)

8.20 EB Error (Hot Water Overheating)

9 Components Replacement Instructions

9.1 Preparation Step

9.2 Control Board

9.3 Sensor, Heating/Return

9.4 Sensor, DHW

9.5 Exhaust Temperature Sensor_T4 (Blue)

9.6 Gas Oriﬁ ce

9.7 Air Pressure Switch

9.8 Gas Valve

9.9 High Limit Cutout HEX T2 (302°F)

9.10 High Limit Cutout Supply T3 (203°F)

9.11 Ignition Transformer

9.12 Electrode Assembly

9.13 Flame Rod

9.14 Touch pad

9.15 Condensation Trap

9.16 Turbo Fan

9.17 Solenoid Valve

9.18 Heat Exchanger

10 Flushing the Heat Exchanger

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 3 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: