manualshive.com logo in svg

Bosch Singular 4000, Руководство по обслуживанию, Страница: 12 / 68

Поделиться
Скачать
Bosch Singular 4000 Скачать руководство пользователя страница 12

1 2

 |

 

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

7     Key Components Description

7.1     Pump

Part No.

7738007283

Function

 

Carries out combustion by circulating the water in the pipe.

 

Circulates the water when the water temperature is 59°F (15°C) or 
below to prevent the boiler from freezing and bursting.

Failure Event

Unable to detect or measure water pressure change when the pump 
operates.

Effects

 

The device may freeze.

 

The boiler does not operate.

Error Code

—

Diagnostic

 

Visual inspection : Check the circulation pump connection wire

 

Voltage check : Check range of voltage shown below

Color/Number of Wires

BLACK - WHITE

 

ON: AC 120 V ±

 

OFF: 0 V

Table 5

7.2     Turn Down Ratio (TDR) Solenoid valve

Part No.

7738007264

Function

 

To control the amount of mixed gas supplied with TDR of 10:1

 

It uses solenoid valve to control the amount of mixed gas

Failure Event

 

Solenoid valve not closing

 

Solenoid valve not opening

Effects

 

Frequent On/Off due to excessive heat.

 

Fail to reach the set temperature due to lack of heat

Error Code

—

Diagnostic

 

Visual inspection : Check the Solenoid valve connection wire

 

Voltage check : Check range of voltage shown below

Color/Number of Wires

RED - RED

 

DC : 120 V ±

Table 6

Содержание Singular 4000





































































Отзывы:

Нет отзывов