Bosch Singular 4000 Скачать руководство пользователя страница 28

Страница: 28 / 68

2 8

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

A6 Error - Main Gas Valve Check

1. Check if the main gas valve is closed.

A6 Error - Gas Valve Check

1. Check the coil for abnormalities.

—

(Normal: 1 – 1.5 kΩ)

If the coil is disconnected and has short-circuited, replace the gas valve.

2. Check the applied voltage of the gas valve. (DC 105 – 135 V)

If the voltage is correct, replace the gas valve, and if the voltage is not
supplied normally, replace the control board.

Figure 19

KΩ

A6 Error - Igniter Check

1. Check the gap of the igniter.

—

Gap: 4 – 5 mm

2. Check the gap between the igniter and the burner.

—

Gap: 8 – 10 mm

A6 Error - Ignition Transformer Check

1. First, remove phillips screw on the ignition transformer and remove

transformer for easier measurement of voltage.

Figure 20

2. Check the input voltage of the igniter

—

Wire color: Brown-Brown (AC 105 – 135 V)

Figure 21

A6 Error - Flame Rod Check

1. Check if the ﬂ ame rod is loose or separated.

2. Check for any foreign material on the ﬂ ame rod (remove any foreign material).

Figure 22

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 28 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: