Bosch Singular 4000 Скачать руководство пользователя страница 21

Страница: 21 / 68

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

8.2 A3 Error (Abnormal Operation: Pump)

Error

Description

Abnormal Pump Operation



Determine whether the pump is in operation when the boiler operation signal is activated



Before operating the pump, check the change in the pressure sensor before and after to see whether there are any
problems in the operation of the pump.

Checkpoint



Check the assembly of the pump connector



Check the operation voltage of the pump

—

Color: White – Black



Check for any clogging of heating water pipes

Table 25

Figure 10

Check the assembly of the

control board and the pump

connector and reassemble

them. Check the operation

of the pump and the flow of

heating water.

Replace the control board

Replace the pump

Power ON / Operation

Check for any clogging of

heating pipes

Check the

pump input

voltage

Whether

the pump is

running

Check for any

clogging of

heating pipes

Yes

White-Black: AC 100 120 V

Replace the control board

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 21 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: