Bosch Singular 4000 Скачать руководство пользователя страница 44

Страница: 44 / 68

4 4

Service Manual

Singular Combi Boiler - BTC 439002301 A (12.2021)

8.15 E1 Error (Abnormal Operation: Exhaust Temperature Sensor)

Error

Description

Hot Water Thermistor_T3 Error

Error is displayed when the Exhaust Thermistor has short-circuited or is disconnected

Checkpoint



Check if the Exhaust Thermistor connector is connected normally.

1. Control board wire
2. E xhaust Thermistor wire



Measure the check the resistance of the Exhaust Thermistor (NTC method).

—

Separate the sensor and measure it at room temperature.



Check the Exhaust Thermistor for disconnection



Check the Exhaust Thermistor for short-circuit

Table 35

Figure 59

Check the assembly

condition of the control board

and the temperature sensor

connector and reassemble

the control board and the

temperature sensor connector

Replace the temperature

sensor

Replace the temperature

sensor

Replace the control board

Check the

temperature

sensor for short

Is the

resistance of the

temperature sensor

normal?

Yes

86 °F: 7.05 kΩ (± error possible)
140 °F: 2.5 kΩ
185 °F: 1.2 kΩ

Содержание Singular 4000





































































Результаты поиска

Содержание Singular 4000

Отзывы:

Bosch Singular 4000, Руководство по обслуживанию, Страница: 44 / 68

Результаты поиска

Содержание Singular 4000

Отзывы: