Bernal G 501, Руководство пользователя

Страница: 24 / 62

24
GB
Press the desired button channel 1, 2, 3 or 4 on the radio hand
transmitter until the drive (see programming manual) or the
radio hand transmitter (simultaneous lighting up of the green
LED and the red LED) confirms successful programming.
Repeat the procedure for additional „B-WAY“ radio hand trans-
mitters (or further channels on the same radio hand transmit-
ter for further functions). Finally leave the programming screen
(occurs within about 60 sec. if there is no action; the drive /
receiver moves back automatically into operational readiness).
NOTE: every channel of a radio hand transmitter can only be
programmed for one garage door drive.
Examples:
- all 4 channels (buttons) of a radio hand transmitter can be
programmed one after the other for 4 different functions of the
same garage door drive or
- all 4 channels (buttons) of a radio hand transmitter can be
programmed one after the other for the same function on the
same garage door drive (a safety function „Operation using any
button“).
- all 4 channels (buttons) of a radio hand transmitter can be pro-
grammed respectively for any desired function on 4 different
garage door drives or
- two channels (buttons) of a radio hand transmitter can be pro-
grammed one after the other for respectively two functions on
2 different garage door drives.
- It is not possible, for example, to programme Channel 1 (Button
1) of the same radio hand transmitter, one after the other, for a
number of different garage door drives. If a channel which has
already been programmed in a garage door drive is program-
med into another garage door drive then the previously pro-
grammed garage door drive will be removed from the memory.
2.2.1 – 2.3.5
The following information refers to the integral bidirectional ra-
dio system BERNAL „B-WAY“.
General information:
For the bidirectional functions of the radio hand transmitter „B-
WAY“ (status enquiry, range checking, battery condition indica-
tor) please consult the manual for the radio hand transmitter.
Up to 128 „B-WAY“ radio hand transmitters can be programmed
dependent on the free storage space.
Hand transmitter remote control is available with the Home-
wave-Control-Box (HWC): For a description of the functions see
the operating manual for the HWC (WLAN uplink to the internet,
HWC web service software and a compatible peripheral device
(tablet, laptop, PC) with an internet connection are necessary.
Operation and status enquiries over a smart phone are availab-
le with HWC and a BERNAL app (an IOS or Android compatible
smart phone with WLAN is necessary). The HWC and a BER-
NAL app simply need to be programmed once like a radio hand
transmitter in the drive.
Only for the version of the device without a display: acceptance
testing of the drive hood is essential for performing the pro-
gramming / deletion of radio hand transmitters (Figure 35)–the
covers on the 230 V/AC area of the control board (see Figure
40) should never be removed!
6.1 PROGRAMME A RADIO HAND TRANSMIT-
TER
Every „B-WAY“ radio hand transmitter must be programmed
once in the receiver memory of the garage door drive. This mes-
sage remains if there is a power cut (power failure; changeover
to battery power). „B-WAY“ should be held at arms length from
the drive/receiver during the programming process.
Perform the programming of the radio hand transmit-
ter on the basis of the programming manual after you
have informed yourself about the general processing
sequence from the following information.
Activate programming and enter menu C-1. Enter (Programme a
hand transmitter). The drive signals „Wait for the hand transmit-
ter“ (see programming manual). Select the desired hand trans-
mitter function:
1 Door run (remote control of the door)
2 Ventilation (remote control of the ventilation function)
3 Light (remote control of the integral drive light)
4 Relay (remote control of the relay “PK”)
6. RADIO (MENU C)