manualshive.com logo in svg

Berges ACM S2, Руководство по эксплуатации, Страница: 56 / 64

Поделиться
Скачать
Berges ACM S2 Скачать руководство пользователя страница 56

18. Faults and remedies

The inverter is equipped with devices for error detection and error signalling.

Error signals are routed to the error signalling relay (250V AC 1A; terminals 122, 123 and 124) and
shown on the display.

Fault

Possible cause

Fault remedy

Motor does not run

No mains voltage

Check mains voltage.

ENABLE or START/STOP
missing

The motor can start only when both
signals are active and when a setpoint
deviating from 0 is present.

Setpoint missing

Check setpoint at terminal 8 or 29.

Unit not connected correctly

Check all connections.

Motor blocked

Check drive.

Internal inverter fault

Sending unit for repair.

Motor runs too slowly

“Fmax” is set too low

Increase “Fmax”.

Setpoint not sufficient
(terminal 8 or 29)

Check setpoint.

Motor running with slip

Increase acceleration time or reduce
“Fmax”.

Output current of inverter too high U/f ratio incorrect

Set new U/f ratio or reduce “Fmax”.

Overcurrent during acceleration

Starting torque too high

Reduce starting torque.

Acceleration time too short

Increase acceleration time.

Motor running with slip

Increase acceleration time.

Overvoltage

Mains voltage too high

Measure mains voltage.

Voltage peaks caused by
switching large loads on the
network

Determine cause and take counter-
measures (e.g. mains filter).

Braking operation

Increase deceleration time or use
external braking chopper.

Heat sink temperature too high

Output stage overloaded

Check ambient temperature of inverter.
Check whether inverter is correctly
dimensioned for the application.

                                                                                                                                                                   BERGES electronic

54

Operating manual   ACM  D2/S2

09.07.2001

Содержание ACM S2

































































Отзывы:

Нет отзывов