manualshive.com logo in svg

Berges ACM S2, Руководство по эксплуатации, Страница: 27 / 64

Поделиться
Скачать
Berges ACM S2 Скачать руководство пользователя страница 27

1) Inverter stopped. Automatic error reset as soon as the link voltage rises above the

undervoltage value.

2) Inverter stopped. If the AUTORESET function is activated (see TAB3, SUB XPAR, function

SW3), a reset is possible by setting or the START/STOP input, or the ENABLE input, or by
setting the setpoint to zero.

3) The motor is decelerated with the deceleration ramp and the inverter is stopped. An error

reset can be performed as described in Item 2.

4) The motor is decelerated with the deceleration ramp and the inverter is stopped until the

temperature doesn’t fall below the limit value. If the AUTORESET function is activated
(see TAB3, SUB XPAR, function SW3), a reset is possible by setting or the START/STOP
input, or the ENABLE input, or by setting the setpoint to zero.

5) Behaviour with Softw. D2A-STD:  see 4)

Behaviour with Softw. D2A-1300: see 2)

14.8. Hardware error messages

An error which is established during the self-test phase or during operation is shown on the display
by the message “ERROR” together with an error number. The inverter is stopped by the safety
devices.

To reset the error message, switch off the mains supply and switch back on again. If the error  is
not rectified by this, send the unit to the after-sales service for inspection.

Error

Cause

Remedy

Data error

Reprogram parameters.

Hard- and
software is not
compatible

Have unit checked by technical after-sales service.

CPU error

Keypad error

Error in ROM

Watchdog error

Clock error

Program error

Output stage error

ERROR 1

ERROR 2

ERROR 3

ERROR 4

ERROR 5

ERROR 6

ERROR 7

ERROR 8

ERROR 9

                                                                                                                                                                   BERGES electronic

09.07.2001

Operating manual   ACM  D2/S2

25

Содержание ACM S2

































































Отзывы:

Нет отзывов