Berges ACM S2 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 64

Berges ACM S2 Скачать руководство пользователя страница 22

Configuration terminal 17:

ACM D2/S2 0.37 - 22.0kW ACM D2 30.0 - 37.0kW
Control board Control board

Digital inputs:            Max. input voltage: +30V DC
               Low - level: 0...1V
                High - level 4...30V

Error signalling relay: 250V AC 1A

Signalling relay: 24V AC/DC 1A

Open-collector outputs: 24V DC 100mA

12.8. Power terminals

Term. Function Description

L1

Single-phase mains power
supply

220...240V

N Neutral conductor Connect with the neutral conductor of the mains supply.

L1

Three-phase mains power
supply

380...460V (5.5kW 380...415V)

L2

L3

PE Mains ground The inverter, motor and accessories must always be earthed.

Br External braking resistor Connection for external braking resistor.

+

DC-link DC-link output.

−

U

Motor terminals

3x0...U

IN

0...650 Hz (0...1300Hz vers. D2A-1300-xxx)

V

W

PTC Motor overtemprature

protection input

Inputs non-insulated.

PTC

Never connect input AC-Power to the motor output terminals U, V, W or damage to

the inverter will result.

P

o

w

e

r t

e

rm

in

al

s

BERGES electronic

20 Operating manual ACM D2/S2 09.07.2001

«
...
20
21
22
23
24
...
»

Содержание ACM S2

































































Отзывы:

Нет отзывов