Berges ACM S2 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 64

Berges ACM S2 Скачать руководство пользователя страница 20

•

Do not extend the shields with single wires and do not interrupt them if possible.

•

When constructing the switchgear cabinet or the system, separate the power section from the
control section. Eventually provide a shield between power and control section.

•

Wire inductive switching elements (coils of contactors or relays) with RC-elements, free-wheeling
diodes or varistors.

12.5. Mains back-up fuses

External upstream fuses are required to protect the cables and the unit itself. The fuses must be
dimensioned so as to permit starting up and normal operation of motors. To guarantee this , we
recommend the use of the followings slow-blow fuses:

Mains input 1 x 230V

0.37kW 0.55kW 0.75kW 1.1kW 2.2kW

4A 8A 8A 8A 16A

Mains input 3 x 400V

0.75kW 1.1kW 1.5kW 2.2kW 3.0kW 4.0kW 5.5kW

4A 6A 6A 8A 10A 16A 20A

Mains input 3 x 400V

7.5kW 11.0kW 15.0kW 22.0kW 30.0kW 37.0kW

35A 35A 63A 63A 80A 100A

12.6. Ventilation

For all inverters, the permissible ambient temperature of 45 °C must not be exceeded. This
particularly applies if the inverter is installed in a control cabinet, because operation of the inverter
may increase the ambient temperature substantially. Appropriate measures, e.g. installation of a
fan, must be taken if the permissible ambient temperature is almost reached or exceeded under
full loading of the inverter.

BERGES electronic

18 Operating manual ACM D2/S2 09.07.2001

«
...
18
19
20
21
22
...
»

Содержание ACM S2

































































Отзывы:

Нет отзывов