Berges ACM S2 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 64

Berges ACM S2 Скачать руководство пользователя страница 37

Submenu preset frequencies

TAB1

The parameters of this submenu are used to set the three preset speeds.

The sign of the parameter value defines the rotating sense of the
motor (

+

CW,

-

CCW).

In order to permit control of the direction of rotation of the preset frequencies via termi-
nal 15, it is necessary to deactivate the sign

+

or

−

by simultaneously pressing the

keys INC and DEC after setting the desired value.

Refer to the following table for proper selection of preset frequencies.

Function A:

Preset-speed FFIX1

(Default: +5 Hz)

Function B:

Preset-speed FFIX2

(Default: +10 Hz)

Function C:

Preset-speed FFIX3

(Default:

+

20 Hz)

SUB FFIX

Range:

−

650...0...

+

650

(

−

1300...0...

+

1300 Hz *)

*Vers. D2A-1300-xxx

Submenu skip frequencies

TAB1

The parameters of this submenu are used to set up to four different skip frequency
bands. A skip band is set by programming an upper and a lower limit for this band.
Skip bands may be programmed to avoid certain mechanical resonances in the drive
system. If upper and lower limits for a Skip band are equal, this band will be deactiva -
ted.
The setting is done programming a lower and an upper limit for each frequency range.

Function a:

Skip-band 1

lower limit

Function A:

Skip-band 1

upper limit

Function b:

Skip-band 2

lower limit

Function B:

Skip-band 2

upper limit

Function c:

Skip-band 3

lower limit

Function C:

Skip-band 3

upper limit

Function d:

Skip-band 4

lower limit

Function D:

Skip-band 4

upper limit

Range:

0...650

(0...1300 Hz *)

Default: 0 Hz

*Vers. D2A-1300-xxx

SUB FFIX

ATTENTION!

Terminal 23

Terminal 24

Frequency

OFF

OFF

Speed reference

signal

ON

OFF

FFIX1

OFF

ON

FFIX2

ON

ON

FFIX3

A

+

5Hz

B

+

10Hz

C

+

20Hz

SUB FEX

a 0.0Hz

A 0.0Hz

b 0.0Hz

B 0.0Hz

c 0.0Hz

C 0.0Hz

d 0.0Hz

D 0.0Hz

BERGES electronic

09.07.2001

Operating manual ACM D2/S2

35

«
...
35
36
37
38
39
...
»

Содержание ACM S2

































































Отзывы:

Нет отзывов