manualshive.com logo in svg

Berges ACM S2, Руководство по эксплуатации, Страница: 41 / 64

Поделиться
Скачать
Berges ACM S2 Скачать руководство пользователя страница 41

  Submenu logic levels of digital inputs

TAB2

The logic level of digital inputs can be changed between HIGH-and LOW-active. Inputs
(except ENABLE and START/STOP) may be deactivated by setting the corresponding
parameter to OFF.
Any change in this submenu becomes active after a save and a restart of the inverter
(Soft-Reset or POWER ON - Reset). A point in the display indicates that parameter va-
lues were modified but not saved.

ENABLE terminal 11 (OFF not possible)

REVERSING terminal 15

START/STOP terminal 16 (OFF not possible)

PRESET FREQ. 1 terminal 23

PRESET FREQ. 2 terminal 24

RAMP SELECT terminal 25
Motorpotentiometer (increase frequency)
(TAB1, function JOG = MPt)

Motorpotentiometer (decrease frequency)                terminal 26
(TAB1, function JOG = MPt)
DC - Brake when ACM - Synchronizer (Option) is used
(activation ACM - Synchronizer with L8 = OFF)

DC BRAKE                               terminal 30
ACM - Synchronizer (OFF)

SUB LOG

Range:

HIGH, LOW, OFF, ON

Default: LOW

  Submenu speed reference

TAB2

The functions in the submenu SUB REF permit configuration and selection of the
speed reference.

To enter the submenu press both SHIFT and SELECT simultaneously.

SUB LOG

L1  LOW

L2  LOW

L3  LOW

L4  LOW

L5  LOW

L6  LOW

L7  LOW

L8  LOW

SUB REF

                                                                                                                                                                   BERGES electronic

09.07.2001 Operating manual   ACM  D2/S2 39

Содержание ACM S2

































































Отзывы:

Нет отзывов