Berges ACM S2 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 64

Berges ACM S2 Скачать руководство пользователя страница 45

Function PASS: PASSWORD

TAB2

If a password has been assigned (PASSWORD <> "000"), to enter the functions
SECUR and SET PASS, the access code must be entered in this function.

Function SECUR: Security code

TAB2

Setting of the requested security level:

0: SECURITY off.

1: SECURITY Level 1

Parameters can be modified but not saved.
Any attempt to save will be interrupted and the message "SECUR.1" will be
displayed.

2: SECURITY Level 2

Parameters cannot be modified or saved.
Any attempt to modify or save will be interrupted and the message
"SECUR. 2" will be displayed.

Range: 0...2

Default: 0

Function SET PASS: SET PASSWORD

TAB2

This function is used to set a password. If a password has been assigned (PASS -
WORD <> "000"), to enter the functions SECUR and SET PASS, the access code
must be entered in function PASSWORD.

Range: 0...999

Default: 0

Save parameter

TAB2

By pressing both INC and DEC simultaneously the parameter values are stored in the
internal non-volatile inverter memory. At the end of the Save-function the program re-
turns to TAB2, function CLIP.

15.4. Program level TAB3

Program level TAB3

TAB3

The program level functions in TAB3 allows to configure the outputs, to access the dia-
gnostic utilities and to program extended parameters.

PASS 000

SECUR. 0

SET 000

SAVE ??

TAB 3

BERGES electronic

09.07.2001 Operating manual ACM D2/S2 43

«
...
43
44
45
46
47
...
»

Содержание ACM S2

































































Отзывы:

Нет отзывов