Berges ACM S2 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 64

Berges ACM S2 Скачать руководство пользователя страница 53

16. Braking chopper ACM D2/S2

16.1. Braking chopper 0.37 kW - 1.1 kW (1 x 230V)

The inverters ACM D2 0.37 - 1.1 kW are equipped as standard with an internal dynamic braking
chopper.

Braking resistance: 50 Ohm/50 Watt.

16.2. Braking chopper 0.75 kW - 37.0 kW (3 x 400V)

The inverters ACM D2/S2 0.75 - 37.0 kW are equipped as standard with an control unit for dynamic
braking chopper. Brake operation is possible after connection of an external brake resistor.

16.2.1. Minimum values for braking resistors (accessory)

The permitted minimum values for braking resistors depend on the respective inverter t ype and are
shown in the table below. The power rating of the braking resistors must be selected corresponding
to the required braking power.

Inverter Minimum braking resistance

ACM S2 2.2 kW (230 V) 47 Ohm

ACM S2 0.75 - 4.0 kW (400 V) 75 Ohm

ACM D2 5.5 - 37.0 kW (400 V) 20 Ohm

16.2.2. Assembling the braking resistor

The braking resistor is connected to terminals (+) and (Br) of the terminal strip. The length of the
connecting cables must not exceed 2 m.

The safety notes in this manual (Chapter 2, Page 3) must be followed exactly if work is

performed inside the inverter!

The braking resistor must be equipped with a temperature monitoring device which insulates the
inverter from the mains supply if the braking circuit is overloaded.

BERGES electronic

09.07.2001 Operating manual ACM D2/S2 51

«
...
51
52
53
54
55
...
»

Содержание ACM S2

































































Отзывы:

Нет отзывов