Berges ACM S2 Скачать руководство пользователя страница 47

Страница: 47 / 64

Submenu extended parameters

TAB3

Setting of eigth extended inverter parameters.

To enter the submenu press both SHIFT and SELECT simultaneously.

Function SW1: DC - Brake

TAB3

This function controls the motor at the end of the DC-brake operation.

ON: The motor stops at the end of the DC-brake time. To restart the motor

open and than close START/STOP or ENABLE.

OFF: The motor will restart automatically at the end of the DC-brake time.

SUB XPAR

Range: ON, OFF

Default: ON

Function SW2: Input config. START/STOP and REVERSING

TAB3

OFF: Terminal 16 = START/STOP

Terminal 15 = REVERSING

ON: Terminal 16 = START CW

Terminal 15 = START CCW

SUB XPAR

Range: ON, OFF

Default: OFF

Function SW3: Error reset

TAB3

This function defines how the drive can be resetted after an error (except hardware er-
rors).

ON: To reset the drive open and then close START/STOP or ENABLE or set

the speed reference signal to zero. (This works only when f-min = 0 and with
no preset frequency selected).

OFF: To reset the drive execute a Soft - Reset or POWER ON - Reset.

SUB XPAR

Range: ON, OFF

Default: ON

Function SW4: Fmin configuration

TAB3

This function defines the inverter behaviour at Fmin. Two different settings are possi -
ble (see the following diagramm).

SUB XPAR

Range: ON, OFF

Default: ON

SUB XPAR

SW1 ON

SW2 OFF

SW3 ON

SW4 ON

Fmin : Value TAB1, function 4.
f

: Output frequency.

Speed ref. : Speed reference value.

BERGES electronic

09.07.2001 Operating manual ACM D2/S2 45

Содержание ACM S2

































































Результаты поиска

Содержание ACM S2

Отзывы:

Berges ACM S2, Руководство по эксплуатации, Страница: 47 / 64

Результаты поиска

Содержание ACM S2

Отзывы: