manualshive.com logo in svg

Berges ACM S2, Руководство по эксплуатации, Страница: 5 / 64

Поделиться
Скачать
Berges ACM S2 Скачать руководство пользователя страница 5

1. General information

Before you start with the installation and the starting up of the inverter, please read this manual carefully
and pay special attention to the notes and suggestions.

This manual must be made available to every user. Before working with the unit the user must become
familiar with it. This specially applies to the knowledge and observance of the following safety and
warning indications.

Used symbols:

Danger, warning

This symbol is used when the life or health of the user is in danger or a considerable damage to property
can occur.

Attention, essential measure

This symbol is shown on places of the manual, which are to be particularly considered for safe and
disturbance-free operation of the inverter.

2. Safety instructions

All instructions stated in this chapter are important for the security of users and machines or systems
and should absolutely be considered.

2.1. General safety instructions

Inverters work with high voltages, which can cause death or serious injury by touching them. Depending
on the degree of protection of the inverter, in operation they may have live, uninsulated and possibly
also moving or rotating parts, as well as hot surfaces. In case of an inadmissible removal of the required
covers, an improper use and a wrong installation or operation, there is a danger of serious personal
injury and damage to property.

All operations serving transport, installation and commissioning as well as maintenance are to be
carried out by skilled technical personnel (observe IEC 364 or CENELEC HD 384 and national accident
prevention rules!). For the purposes of these basic safety instructions, "skilled technical personnel"
means persons who are familiar with the installation, mounting, commissioning and operation of the
product and have the qualifications needed for the performance of their functions.

2.2. Intended use

The application of the inverter described in this operating manual exclusively serves for the purpose
of continuously variable speed control of three-phase motors.

Inverters are components designed to be used in electrical installations or machinery.

Commissioning of the inverter (e.g. the starting of normal operation) is prohibited until the system has
been proved to conform to the provisions of the directive 89/392/EEC (Machinery Safety Directive -
MSD) and the  89/336/EEC (EMC directive).

The inverter meets the requirements of the low-voltage directive 73/231/EEC. They are subject to the
harmonized standards of the series EN 50178.

The operator of the system is solely liable for damage resulting from improper use of the inverter.

ATTENTION!

                                                                                                                                                                   BERGES electronic

09.07.2001 Operating manual   ACM  D2/S2 3     

Содержание ACM S2

































































Отзывы:

Нет отзывов