Bender ATICS Series Скачать руководство пользователя страница 73

Страница: 73 / 104

ATICS-DIO_D00080_03_M_XXEN / 04.2021 73

ATICS-…-DIO

Adjusting the settings:

Menu

Description

Exit

Exit settings menu "Relay"; go up one menu level

1. Function

ALARM

Relay switches if at least one of the following menus 3…9 is set

to "on" and the corresponding alarm message appears.

Active

Relay switches if at least one of the following menus 3…9 is set

to "on" and the corresponding alarm message does

not

appear

(operating message). If several of these menus are set to "on",

none of them must have an alarm in order to be able to activate

the

relay.

Application example:

Function = "Active"

Line 1 = "on", all other menus (line 2, device error, etc.) are set to

"off".

-> Relay is activated when line 1 is ready for operation.

GenSt

Relay is used as Generator start relay (

alarm relay 1 only

)

2. Relay mode

N/O

N/O operation. Relay only switches in the event of an alarm.

N/C

N/C operation. Relay only switches in the event of an alarm.

N/O-T

N/O operation. Relay switches in the event of an alarm or a test.

N/C-T

N/C operation. Relay switches in the event of an alarm or a test.

3. Line 1

Line 1

off

4. Line 2

Line 2

off

5. Manual mode

Relay switches in manual mode (transparent cover open or

digital input "Manual mode" selected).
off

6. Device error

Internal device error 1.x, 3.x (except 3.50), 6.x, 7.x, 8.x, 9.x or BMS

bus has no master, short-circuit distribution board, failure distribution board, test due,
service due.
off

7. Test interval

Relay switches when a test is due (interval elapsed).

off

8. Serviceinterv.

Relay switches when service is due (interval elapsed).

off

9. Dig. input

Alarm digital input. To ensure that the relay responds to the dig-

ital input, the functions "ALARM" or "R-OPL" must be additionally set in the "Settings
-> Dig. input" menu.
off

Содержание ATICS Series









































































































Результаты поиска

Содержание ATICS Series

Отзывы:

Bender ATICS Series, Руководство пользователя, Страница: 73 / 104

Результаты поиска

Содержание ATICS Series

Отзывы: