Bender ATICS Series Скачать руководство пользователя страница 61

Страница: 61 / 104

ATICS-DIO_D00080_03_M_XXEN / 04.2021 61

ATICS-…-DIO

7.3

Function of the main menu

Menu item

Function

Page

Exit

Exit menu mode

1. Alarm/meas.values

Display saved status messages, alarm messages and measured values

P. 61

2. Changeover

Display information on the changeover function (number, test)

P. 64

3. History/Loggers

Display history memory, data logger, configuration logger, test logger and
service logger

P. 64

4. Settings

Various settings for this device

P. 66

5. Control

Run TEST and RESET of this device

P. 81

6. Dig. input

Display voltage level of the digital input

P. 81

7. Info

Display information on device type and firmware versions

P. 82

7.3.1 Menu 1: Alarm/meas.values

Display current status messages, alarm messages and measured values. The device shows the alarm sta-
tus for each menu item: = no alarm, = alarm.

7.3.1.1 Alarm/meas.values ATICS-2-DIO

Menu

Description

Exit

Exit "Alarm/meas. values" menu; go up one menu level

1. Line 1: 228V

Line 1: Measured value mains voltage

2. Line 2: 183V

Line 2: Measured value mains voltage

3. Position: 1

Switch position of the automatic transfer switching device

4. t(2->1):--
or
4. Switch-back lock

Return transfer delay time is enabled, seconds counting backwards
or
Switch-back lock enabled

5. Automatic mode

Automatic mode or manual mode

6. Status

Device error (e.g.: no BMS bus master present)

7. I(3):35A

Load current in the TN system or "No CT connected" fault

8. Dig.input:

Alarm digital input 1
(see chapter „Settings menu 5: Dig. input“ on p. 74)

9. Dig.input:

Alarm digital input 2
(see chapter „Settings menu 5: Dig. input“ on p. 74)

10. Dig.input:

Alarm digital input 3
(see chapter S. 74)

11. Dig.input:

Alarm digital input 4
(see chapter „Settings menu 5: Dig. input“ on p. 74)

Содержание ATICS Series









































































































Результаты поиска

Содержание ATICS Series

Отзывы:

Bender ATICS Series, Руководство пользователя, Страница: 61 / 104

Результаты поиска

Содержание ATICS Series

Отзывы: