Belarus 80.1 Series Скачать руководство пользователя | Manualshive

Страница: 40 / 143

background image

Belarus 80.1/80.2/82.1/82.2/82

Р — Operation and Service Manual

Section 6. Operating and Adjusting Regulations

44

6.3. STARTING THE DIESEL-ENGINE

Start-Up Under Normal Conditions:

Check  the  oil  level  in  the  diesel-engine
crankcase  and  the  coolant  level  in  the
radiator,  as  well  as  the  presence  of  fuel
in the fuel tank.

IMPORTANT!

DO NOT start up the die-

sel-engine if the cooling system is not
filled up.

IMPORTANT!

Starting up the diesel-

engine and instrument control procedure
should only be initiated with the driver
being on the operator

’s seat.

CAUTION:

NEVER operate the tractor in

closed spaces.

1. Apply the parking brake on the tractor;

2. Set the gear shift lever (2) to the neu-
tral, and the step-down reducing gear
lever (9) into its extreme position (either
backward or forward);

3. Set the P.T.O. control lever (3) to the
position «Engaged»;

4. Set the "frame" switch (4) ON;

5. Set the fuel feed lever (5) into its mid-

position;

6. Push down hard on the clutch pedal

(6);

7. Turn the starter key (7) into position II

(«Start») and hold it in this position un-
til  the  diesel-engine  picks  up,  but  not
in  excess  of  15  s.  Therewith,  a  start-
up warning lamp alights in the warning
light  in-line  panel  (8)  (refer  to  Sheet
32,  Ref.  4).  Once  the  diesel-engine
has  started,  the  lamp  should  go  off.
Should  the  diesel-engine  fail  to  start,
repeat  the  starting  procedure  not  ear-
lier than in

30…40 seс.

ATTENTION!

If the starter would not

switch  on  and  the  starter  control  unit
warning  lamp  blinks  at  a  low  frequency
(about 1,5 Hz), it means that the GB shift
lever  is  not  in  the  neutral  or  there  is  a
break  in  the  start-up  interlock  circuit.  If
the  lamp  flickers  at  higher  frequency
(about 3 Hz), the trouble is in the alterna-
tor circuit (terminal «W» or «~»).

8. Release the clutch pedal (6). When

the diesel-engine is running, check
operation of all the warning lights and
instrument readings (coolant tempera-
ture, oil pressure in diesel-engine,
storage batteries charging).

Let the diesel-engine run at 1000

r.p.m. until oil level stabilizes within
the operating range.

«
...
38
39
40
41
42
...
»

Содержание 80.1 Series
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80.1 Series

Бренд: Komatsu Страницы: 195

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 72

Бренд: Craftsman Страницы: 28

Бренд: GOLDONI Страницы: 76

Бренд: R2 RINALDI Страницы: 26

Бренд: Ventrac Страницы: 53

Бренд: Cub Cadet Страницы: 33

Бренд: Hagie Страницы: 97

Бренд: MAGNATRAC Страницы: 86

FORTERRA HSX 100 2014

Бренд: Zetor Страницы: 250

Бренд: Hardi Страницы: 170

Groom Master II 88008

Бренд: Jacobsen Страницы: 104

Бренд: GE Страницы: 12

Бренд: Thwaites Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды