Belarus 80.1 Series Скачать руководство пользователя страница 132

Страница: 132 / 143

Belarus 80.1/80.2/82.1/82.2/82

Р —Operation and Service Manual

Section 10. Common troubles and their remedies

123

Table 14, continued

Trouble, External Symptoms

Remedy

C. Blue smoke from the exhaust pipe

Oil in the combustion chambers due to wear in the
sleeve assembly.

Replace worn-out parts of the sleeve assembly.

Excess of oil in diesel-engine crankcase.

Drain excessive oil and bring oil level to top mark of
the dipstick.

Diesel Engine Overheated

Coolant in the cooling system boiling.

Clean the radiator from dust and dirt. Clean the
cooling system from scale, if needed, and readjust
the fan belt tension, if required.

Poor fuel atomization by nozzles.

Identify faulty nozzles; clean, flush and adjust them.

Oil Pressure in Warmed-Up Diesel-Engine Lower Than That Admissible

Pressure gauge faulty.

Replace the pressure gauge.

Oil pump faulty in the diesel-engine lubrication sys-
tem.

Locate and remedy the fault or replace the pump.

Oil level in the diesel-engine crankcase lower than
the admissible one.

Top up oil to the upper mark on the dipstick.

Safety valve jammed in the centrifugal oil filter
body.

Flush the valve through and adjust pressure.

Maximum wear-out of crankshaft journal-to-bearing
mating.

Have the diesel-engine sent to workshop for repair.

10.2. POWER TRAIN

10.2.1. CLUTCH

Clutch Fails to Transmit Torque in Full

No free travel of the clutch pedal.

Adjust the pedal free travel.

Driven disk linings worn-out.

Replace the linings or the driven disk assembly.

Clutch Fails to Disengage in Full

Clutch free travel excessive.

Adjust the clutch pedal free travel.

Oil in Dry Section of the Clutch Housing

Crankshaft seal collar worn-out.

Replace the collar.

Flexing of the P.T.O. driven shaft beating cover
when joining the tractor after repair

Install a new cover or straighten the old one.

Износ манжеты кронштейна отводки

Замените манжету

10.2.2. SPEED GEARBOX

GB Gears Shift with Gritting

Incomplete engagement of the clutch; the clutch
drags.

Adjust the pedal free play.

10.2.3. MAIN DRIVE

Increased Noise in the Bevel Gears Pair

Adjustment of main drive bevel gearing and differ-
ential bearings disturbed.

Adjust gear meshing and bearing clearances.

Содержание 80.1 Series
















































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды

Belarus 80.1 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды