Belarus 80.1 Series Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 143

background image

Belarus 80.1/80.2/82.1/82.2/82

Р — Operation and Service Manual

Section 7. Maintenance Procedures

75

TYPES OF MAINTENANCE PROCEDURES

Table 7

Type of maintenance procedures

Maintenance intervals and terms of servicing ex

in tractor operating hours

fuel to be consumed,

kg

Pre-operation servicing

Pre-running-in MS

Prior to tractor running-in

MS in process of running-in

MS during running-in

Post-running-in maintenance service

After 30 operating hours

Schedule maintenance:

Inter-shift maintenance servicing (ISM)

8-10

Maintenance service schedule No. 1 (MS-1)

125

1050

Maintenance service schedule No. 2 (MS-2)

500

4200

Maintenance service schedule No. 3 (MS-3)

1000

8400

Seasonal maintenance procedures (MS-SS and
MS-AW)

In  preparation  for  Autumn-
Winter  (MS-AW)  operation
and  Spring-Summer  (MS-
SS) driving period

MS under special service conditions

In preparation for operation
under special service condi-
tions

Maintenance service procedures when in storage

7.1. MAINTENANCE SERVICE OF THE
TRACTOR IN PREPARATION FOR
FIRST OPERATION

7.1.1. Maintenance Service in Prepara-
tion of Tractor for Running-In

а) clean the tractor from dust and dirt,

remove protective grease (if applied
on the tractor);

b) check the level of oil and top up, if re-

quired,  in:  the  diesel-engine  crank-
case;  air  cleaner  oil  pan;  hydraulic
system tank; hydraulic steering boost-
er  body;  housing  of  power  transmis-
sion;  FDA  housing;  FDA  wheel-hub
reducing  gear  housings;  intermediate
bearing;  rear axle  hub  reducing  gears
for tractor Belarus-82P;

c) lubricate the clutch release bearing,

steering  knuckle  bearings;  right-hand
drop  link  pinion;  rear  hitch  linkage
shaft  bushings;  HSCU  hydraulic  cylin-
der joints (if installed);

d) check the storage battery, dress ter-

minals  from  oxide  films,  and  smear
them  with  petroleum  jelly;  clean  the
vent  holes  of plugs;  check the degree
of discharge;

e) check and adjust, if required, the fol-

lowing: tensioning of the fan driving
belt; tractor steering and control mech-
anisms; inflation pressure in tyres; front
wheel toe-in;

f) check and tighten up, if required, ex-

ternal threaded joints;

g) fill in the radiator with coolant;

h) listen to the running diesel-engine and

check to see that instruments and
gauges read within the prescribed
specifications.

«
...
80
81
82
83
84
...
»

Содержание 80.1 Series
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80.1 Series

Бренд: Wallenstein Страницы: 48

Бренд: Grouser Products Страницы: 20

Бренд: Black Widow Страницы: 4

Бренд: Agriweld Страницы: 11

Бренд: Valtra Страницы: 11

IHIMER CARRY 107

Бренд: IHI Страницы: 48

Бренд: Cub Cadet Страницы: 32

Бренд: Cub Cadet Страницы: 32

Бренд: Tiger Страницы: 202

BENGAL JD6110-20M/R MY20

Бренд: Tiger Страницы: 223

BENGAL JD6110-30M/R T4F

Бренд: Tiger Страницы: 226

WILDKAT JD6105-25E T4F

Бренд: Tiger Страницы: 240

Бренд: Tiger Страницы: 236

BENGAL JD51 M Series

Бренд: Tiger Страницы: 240

WILDCAT JD6105D

Бренд: Tiger Страницы: 252

WILDKAT JD61 M/R Series

Бренд: Tiger Страницы: 258

BENGAL 5085M Series

Бренд: Tiger Страницы: 294

Бренд: homelabs Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды