Belarus 80.1 Series Скачать руководство пользователя | Manualshive

Страница: 94 / 143

background image

Belarus 80.1/80.2/82.1/82.2/82

Р — Operation and Service Manual

Section 7. Maintenance Procedures

87

7.6. SCOPE AND SEQUENCE OF
BASIC MAINTENANCE SERVICE AND
ADJUSTMENT OPERATIONS

7.6.1. Diesel-Engine

CHANGE OF OIL IN THE DIESEL-
ENGINE CRANKCASE

When changing oil in the diesel-engine
crankcase, follow the directions as fol-
lows:

а) use in the oil sump only oil recom-

mended in this Manual, correspond-
ing to the season of operation;

b) fill in oil up to the top mark on the oil

dipstick. DO NOT run the diesel-engine
when oil  level  is  below  the  lower mark
or  above  the  upper  mark  on  the  dip-
stick; check the level not earlier than in
3-5  min.  after  the  diesel-engine  has
been stopped;

c) change oil in the diesel-engine

crankcase every 500 hours (during
scheduled MS-2).

To drain oil from the lower part of the
diesel-engine crankcase, there is a hole
stopped with a plug.

CHECKS AND ADJUSTMENT OF
CLEARANCES IN DIESEL-ENGINE
VALVES

After  running-in  a  new  tractor  and  every
500 hours, as well as when removing the
cylinder  heads,  tightening  up  attaching
bolts of the cylinder head and in case of
valve  knocks,  check  and  adjust  valve-
and-rocker

arm

clearances

(during

scheduled MS-2).

The clearance between the rocker-arm
face and the valve stem butt-end on a
cold diesel-engine is to be adjusted with-
in 0.25...0.30 mm for exhaust and intake
valves.

To adjust, proceed as follows (see Fig.
35):

а) remove the hood of the cylinder head

cover;

b) check the rocker arm shaft support

attachment for tightening;

c) set the first cylinder piston to the

TDC (both valve should be closed);

г) loosen lock-nut (2) of the screw on

the rocker arm of the valve to be ad-
justed  and,  driving  screw  (1)  in  or
out,  set  the  required  clearance  be-
tween  the  rocker  arm  face  and  the
valve  stem  against feeler  gauge  (3).
When  the  clearance  is  set,  tighten
the  lock-nut  and  again  check  the
clearance  with  the  feeler  gauge,  ro-
tating  the  shaft.  The  valves  should
be  adjusted  in  a  sequence  which
agrees  with  the  cylinder  firing  order
of  the  diesel-engine  (1-3-4-2),  rotate
the  crankshaft  1/2  turn  more,  in  the
clockwise direction.

Fig. 35. Adjustment of diesel-engine valve

clearances.

«
...
92
93
94
95
96
...
»

Содержание 80.1 Series
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80.1 Series

Бренд: Ditch Witch Страницы: 103

Бренд: Yanmar Страницы: 202

Бренд: Branson Страницы: 132

Бренд: Valtra Страницы: 41

Бренд: Mahindra Страницы: 87

Бренд: ICS Страницы: 18

Бренд: KitchenAid Страницы: 6

Бренд: KitchenAid Страницы: 12

Бренд: KitchenAid Страницы: 1

Бренд: KitchenAid Страницы: 12

Proxima Plus 105

Бренд: Zetor Страницы: 197

PROXIMA PLUS 100 2012

Бренд: Zetor Страницы: 212

Бренд: Verts Loisirs Страницы: 72

Бренд: BROWNS Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды