Belarus 80.1 Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 143

background image

Section 7. Maintenance Procedures

Belarus 80.1/80.2/82.1/82.2/82

Р — Operation and Service Manual

74

7. MAINTENANCE PROCEDURES

Servicing  of  the  tractor  is  a  scheduled
maintenance  that  implies  the  fulfillment
of  operations  which  ensure  operative
condition  and  efficient  operation  of  the
machine  within  the  limits  of  specified
service life.

Carry out maintenance works in time and
in the scope recommended in this Manu-
al. Depending on tractor operating condi-
tions,  departure  from  the  prescribed  in-
tervals  in-between  maintenance  sched-
ules  is  permissible  within  ±10  percent.
The  tractor service log-book should con-
tain  all  the  records  to  be  entered  after
each maintenance  service  schedule  car-
ried out on the machine.

ATTENTION!

In  the  course  of  servicing  the  hitch
linkage  hydraulic  system  and  steering
controls  of  the  tractor,  close  ob-
servance  of  oil  change  and  filter  (ele-
ments)  replacement  intervals  is  a
must. Filling (refilling) of oils which are
not  recommended  by  the  Tractor  Op-
eration  and  Service  Manual  is  imper-
missible.

Before  filling  in  the  system  and/or  re-
placement of filter elements, clean  fill-
er plugs, throats, filter caps and adjoin-
ing  surfaces  from  dust  and  dirt.  When
replacing  filter  elements,  be  sure  to
flush the inner surfaces of filter bodies
and caps.

When the tractor is ganged-up with ag-
ricultural hydraulically-controlled ma-
chines or implements, clean thoroughly
clutches, connection unions, adapters
and other standard fittings of farm ma-
chines and the tractor.

In  the  case  of  hydraulic  hitch  linkage
system  operating  under  heavy  loads,
as well as in combination with hydrau-
lically  controlled agricultural machines,
whose systems are filled with oil of un-
known  origin,  it  is  strongly  recom-
mended  to  cut  the  intervals  between
filter elements replacement.

Keep  firmly  in  mind  that  pure  and
clean  oil  in  the  hydraulic  system
guarantees  its  trouble-free  operation

.

«
...
79
80
81
82
83
...
»

Содержание 80.1 Series
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80.1 Series

Бренд: Rankin Страницы: 37

Бренд: Jenn-Air Страницы: 3

TC507W - Jenn-Air Trash Compactor

Бренд: Jenn-Air Страницы: 28

Бренд: Amica Страницы: 16

Бренд: New Holland Страницы: 81

Бренд: Wheel Horse Страницы: 12

Бренд: FENDT Страницы: 6

Бренд: Husqvarna Страницы: 72

Бренд: Black Widow Страницы: 4

Proxima 100 2012

Бренд: Zetor Страницы: 214

Бренд: Hayter Страницы: 28

Бренд: Hayter Страницы: 52

Бренд: DTA Страницы: 8

Бренд: MASSEY FERGUSON Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды