BECKWITH ELECTRIC M-4272 Скачать руководство пользователя страница 128

Страница: 128 / 217

System Setup and Setpoints – 4

4–17

15.

Press

EXIT

, the ethernet board will

reconfigure and the following will be
displayed:

CONFIGURING ETH...

If the ethernet board is successfully
configured, then the entered IP Address
will be displayed for approximately 2
seconds:

ETHERNET IP ADDRESS

xx.xx.xx.xx

The ethernet board is now configured for use and
may be accessed through a network.

INSTALLING THE MODEMS

Using ISScom

to interrogate, set or monitor the

MBTS using a modem requires both a remote
modem connected at the MBTS location and a local
modem connected to the computer with ISScom
installed.

NOTE

: Any compatible modem may be used;

however, the unit only communicates at
1200 to 9600 baud.

In order to use ISScom to communicate with the
MBTS using a modem, the following must be
provided with the MBTS:

•

An external modem (1200 baud or higher),
capable of understanding standard AT
commands.

•

Serial modem cable with 9-pin connector
for the MBTS and the applicable connector
for the modem.

Similarly, the computer running ISScom must also
have access to a compatible internal or external
modem.

Connecting the PC Modem

If the computer has an external modem,
then use a standard straight-through
RS-232 modem cable (M-3933) to
connect the computer to the modem.

If the computer has an internal modem,
then refer to the modem’s instruction
book to determine which communications
port should be selected.

Verify that the modem is attached to (if
external) or assigned to (if internal) the
same serial port as assigned in ISScom.

While ISScom can use any of the 255
serial ports (COM1 through COM255),
most computers support only COM1 and
COM2.

Connect the modem to a telephone line,
then energize the modem.

Initializing the PC Modem

Verify that the modem is connected as
described in “Connecting the PC Modem”.

Open ISScom, then select the

COMM

menu item.

ISScom will display the Communication
Dialog screen (Figure 4-13).

Select

COMM DEVICE/MODEM,

ISScom will display the Expanded
Communication Dialog screen (Figure
4-14) to include modem setup
information.

Enter the required information in the PC
Modem Settings section of the
Communication screen

Select

INITIALIZE

from the expanded

Communications dialog box.

COMMAND BUTTONS

Serial COM

The Serial COM Port selection allows

Port

the user to select the COM Port, Baud
Rate, Parity and Stop Bits.

Open COM

Initiates contact with the MBTS,
either by direct serial or modem
communication.

Close COM

Breaks communication with the
protective system, for both direct
serial or modem communication.

TCP_IP

Opens the ethernet applicable
communication screen selections to
allow user to enter a TCP_IP address
(if necessary), and opening and closing
communication with the target relay.

Modem

Displays the expanded
Communication dialog box.

Cancel

Returns you to the ISScom main
window; any changes to the displayed
information are lost.

Содержание M-4272


























































































































































































































Результаты поиска

Содержание M-4272

Отзывы:

Бренды по названию

Популярные бренды

BECKWITH ELECTRIC M-4272, Инструкция

Результаты поиска

Содержание M-4272

Отзывы:

Бренды по названию

Популярные бренды