BECKWITH ELECTRIC M-4272 Скачать руководство пользователя страница 126

Страница: 126 / 217

System Setup and Setpoints – 4

4–15

HMI Ethernet Port Setup

Press the

ENTER

pushbutton.

If Level Access is active, the following
is displayed:

ENTER ACCESS CODE

Input the required Access Code, then
press

ENTER

If the proper Access Code has been
entered, the HMI will return:

LEVEL #(1,2 or 3)
Access Granted!

INIT TRANSFER

INIT

rmte_lcal

Go to step 4.

If Level Access is not active, then the
following is displayed:

INIT TRANSFER

INIT

rmte_lcal

Press the Right arrow pushbutton until
the following is displayed:

COMMUNICATION
stat COMM setup

Press

ENTER

, the following will be

displayed:

COM1 SETUP
COM1 com2 com3 com_adr

Use the Right arrow pushbutton to select
ETH (Upper Case).

ETHERNET SETUP

access ETH eth_ip

Press

ENTER

, the following will be

displayed:

ETHERNET
DISABLE enable

Use the Right arrow pushbutton to select
ENABLE (Upper Case), then press

ENTER

, the following will be displayed:

TCP/IP SETTINGS
TCP_SETTINGS

Press

ENTER

, the following will be

displayed:

DHCP PROTOCOL
DISABLE enable

10.

If the network does not support the DHCP
protocol, then go to Manual Configuration
of Ethernet Board (following page) to
manually configure the ethernet board.

11.

If the DHCP Protocol is to be enabled,
then use the Right/Left arrow pushbutton
to select ENABLE (Upper Case), then
press

ENTER

, the following will be

displayed:

TCP/IP SETTINGS
TCP_SETTINGS

12.

Press

EXIT

, the ethernet board will

reconfigure and the following will be
displayed:

CONFIGURING ETH...

If the ethernet board successfully obtains
an IP Address the following will be
displayed for approximately 2 seconds:

ETHERNET IP ADDRESS

xx.xx.xx.xx

The ethernet board is now configured for use and
may be accessed through a network. The display
will return to the following:

ETHERNET SETUP

access ETH eth_ip

Содержание M-4272


























































































































































































































Результаты поиска

Содержание M-4272

Отзывы:

Похожие инструкции для M-4272

Бренды по названию

Популярные бренды

BECKWITH ELECTRIC M-4272, Инструкция

Результаты поиска

Содержание M-4272

Отзывы:

Похожие инструкции для M-4272

Бренды по названию

Популярные бренды