Barnstead EASYpure RO 742 Series Скачать руководство пользователя страница 32

Страница: 32 / 40

Problem

Possible Causes

Solutions

EASYpure RO

No electrical power to

Ensure EASYpure RO

completely inactive.

EASYpure RO.

power cord is installed

(Controls not operating.)

and connected to live power.

Blown fuses.

Check/Replace fuses.
Refer to “Fuse Replacement”
for procedure.

No water flowing (low

Feedwater supply valve

Open feedwater supply valve.

pressure indicator light
illuminated).

Prefilter plugged.

Replace prefilter.

Solenoid valve not open.

Replace solenoid valve.

Feed pressure below

Increase pressure.

specifications.

Illumination of service

Improperly installed

Ensure membrane is

membrane light.

membrane.

installed properly.

Decrease in % rejection.

Fouled membrane.

Replace membrane.

Decrease in system

Decrease in water

If decline in flowrate is

productivity.

unacceptable, install
feedwater temperature valve
to elevate water temperature.

Membrane fouled.

Replace membrane

Low incoming water

Ensure prefilter is not

pressure.

blocked—increase incoming
water pressure.

Low membrane

Increase operating pressure.

operating pressure.

Troubleshooting

Содержание EASYpure RO 742 Series









































Результаты поиска

Содержание EASYpure RO 742 Series

Отзывы:

Похожие инструкции для EASYpure RO 742 Series

Бренды по названию

Популярные бренды

Barnstead EASYpure RO 742 Series, Руководство пользователя

Результаты поиска

Содержание EASYpure RO 742 Series

Отзывы:

Похожие инструкции для EASYpure RO 742 Series

Бренды по названию

Популярные бренды