Bard MULTI-TEC W24AAPA Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 88

background image

Manual 2100-676B

Page

70 of 88

One additional temperature sensor can be added to Zone 1 and additional temperature/humidity sensors may be
added to Zones 2 and 3 (one per zone).

Be sure the sensors are connected to the proper terminals on the terminal

block and sensor as listed below.

FIGURE 22

Additional Remote Temperature and Temperature/Humidity Sensor Installation

For proper operation, the remote indoor temperature/humidity sensor must be configured properly with the controller.
An additional remote indoor temperature-only sensor can be purchased and installed in Zone 1. Also, temperature
and humidity sensors can also be purchased and installed in Zones 2 and 3 (one per zone). For information on
remote indoor sensor configuration, see page 69. For each additional sensor installed, be sure to enable the sensor
in the controller menus (see

Configure Sensors

beginning on page 84).

Zone 1:

Optional Remote

Temperature Sensor

Terminals 20 & 21

*

* The two wire connections for the optional remote temperature sensor

are not polarity sensitive.

TB#

Wire

Mark

Description

20

B7

Indoor Remote Sensor (Zone 1 – optional)

21

GND

Ground

Zone 3:

Optional Remote

Temperature/Humidity Sensor

Terminals 28, 29, 16, 17 & 24

TB#

Wire

Mark

Sensor

Description

28

B9

NTC OUT Indoor Remote Sensor (Zone 3)

29

GND

NTC OUT Ground

16

B4

OUT H

Remote Indoor Humidity Sensor: 0-1 VDC (Zone 3)

17

GND

M (GO)

Ground

24

+VDC

+ (G)

Power for B4

Zone 2:

Optional Remote

Temperature/Humidity Sensor

Terminals 26, 27, 14, 15 & 23

TB#

Wire

Mark

Sensor

Description

26

B8

NTC OUT Indoor Remote Sensor (Zone 2)

27

GND

NTC OUT Ground

14

B3

OUT H

Remote Indoor Humidity Sensor: 0-1 VDC (Zone 2)

15

GND

M (GO)

Ground

23

+VDC

+ (G)

Power for B3

Zones 2 and 3 can also use temperature-only sensors in place of the temperature/humidity sensors. Zone 2 will connect
to TB# 26 and 27. Zone 3 will connect to TB# 28 and 29. The wire connections for the temperature-only sensors are not
polarity sensitive.

5

7

9

17

19

21

25

23

27

29

31

35

33

37

11

13

15

39

43

41

45

47

51

49

53

55

59

57

60

6

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

42

44

46

48

50

52

54

56

58

1

2

3

4

«
...
68
69
70
71
72
...
»

Содержание MULTI-TEC W24AAPA

























































































Отзывы:

Нет отзывов

Похожие инструкции для MULTI-TEC W24AAPA

MCM-A200 User Manual (XP)

Бренд: Samsung Страницы: 12

Бренд: Bard Страницы: 12

U LIGHT COMBO TRS2075

Бренд: IconBiT Страницы: 2

Бренд: Airwell Страницы: 7

Бренд: Panasonic Страницы: 23

Бренд: Daikin Страницы: 88

Бренд: Daikin Страницы: 16

Бренд: Kaysun Страницы: 16

Бренд: Carrier Страницы: 4

Бренд: Ballu Страницы: 46

Бренд: Carrier Страницы: 6

Бренд: GE Страницы: 32

Бренд: Seifert Страницы: 20

Бренд: Daikin Страницы: 23

CROWN+ CROWN09HP230V1B

Бренд: Gree Страницы: 28

SplitAir3 SAL40

Бренд: Stulz Страницы: 73

Бренд: HEIL Страницы: 10

Бренд: Zamil Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды