background image

Update Sensor Firmware Using the Ranger Pro Configuration 

Software

When you use the Ranger Pro Configuration Software, there are two methods to update the 

firmware: the USB NFC reader or the over-the-air. You can only use the over-the-air method to 

update devices on a WirelessHART gateway. 

Before you can update sensor firmware, be sure you have downloaded and added current 

versions of the firmware to the application.

Before you update sensor firmware using the NFC reader: 

 

l

Remove each Ranger Pro device from the field. Depending on the number of devices, this 

can be a manually time-consuming process. 

 

l

When you update the firmware, the update is applied immediately.

To use the USB NFC reader to individually update the e-module firmware: 

 1.  Open the Ranger Pro Configuration Software.

 2.  Connect the NFC reader to the computer running the Ranger Pro Configuration Software. 
 3.  Place the Ranger Pro device upside down on the NFC reader pad with the e-module in 

contact with the pad. 

 4.  Select 

NFC Manager

 > 

Firmware Manager

 5.  Select a valid firmware version and click 

Upgrade

 6.  Select 

Network Manager

 > 

Sensors 

 tab. 

 7.  Update progress is displayed in the 

Firmware Version

 field. To cancel, right-click on 

Firmware Version

 and select 

Cancel Firmware Upgrade

. The upgrade may take from 1-5 

minutes. 

 8.  When successful, you can clear the status message. Right-click on the status and click 

Clear Firmware Upgrade Status

 9.  Once complete, the Ranger Pro device automatically reboots. The version number 

displayed in 

Firmware Version

 is updated.

53/56

Ranger Pro Wireless Condition Monitoring Device
User Guide

125M6113 Rev. D

Содержание Bently Nevada Ranger Pro

























































Отзывы: