Aybey Elektronik AE-LIFT Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 53

background image

8.8 MOTOR TUNING

Motor tuning is the process of motor parameter definition. No rotation of motor required in tuning
process.

When entering Tuning Menu, “PRESS UP ARROW for TUNING PROCESS” message displays on the screen.
If K1 and K2 motor contactor controlled by control panel, hold activated during tuning process. By up
arrow, tuning process will start and after 30 seconds, system completed process if no fault occurs. After
process, release motor contactors if controlled by control panel.

Set these parameters before tuning process:

[M01]-Motor Type

[M02]-Motor Speed

[M03]-Motor RPM

[M04]-Motor Frequency

[M05]-Motor Current

[M06]-Motor Voltage

[M07]-Motor Cos Value

[M08]-Motor Poles

[M10]-Encoder Pulse

[M18]-Encoder Type

*** In synchronous motor, hold activated ENB input during tuning process.

F/7.5.5.02.95 R:1

42

AE-LIFT

«
...
43
44
45
46
47
...
»

Содержание AE-LIFT Series






















































Отзывы:

Нет отзывов

Похожие инструкции для AE-LIFT Series

Бренд: Samson Страницы: 44

Бренд: Gama Sonic Страницы: 4

Бренд: YASKAWA Страницы: 4

Бренд: Patton electronics Страницы: 11

Parallel Port Input/Output Converter PPIO

Бренд: B&B Electronics Страницы: 34

Бренд: RGBlink Страницы: 42

Бренд: ICP DAS USA Страницы: 3

Бренд: B&B Electronics Страницы: 2

Бренд: Perle Страницы: 23

Бренд: IONODES Страницы: 23

Бренд: Badger Power Electronics Страницы: 29

Бренд: Lika Страницы: 104

Бренд: Hall Research Technologies Страницы: 8

Бренд: ICP CON Страницы: 8

Бренд: Tripp Lite Страницы: 24

Бренд: Trycom Technology Страницы: 26

Бренд: Bronson++ Страницы: 50

Бренд: UNICOM Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды