manualshive.com logo in svg

Avaya 03-300686, Установка и подключение, Страница: 9 / 156

Поделиться
Скачать
Avaya 03-300686 Скачать руководство пользователя страница 9

Issue 3 January 2008

9

 

Chapter 1: Introduction

This documentation,

 Installing and Connecting the MDF and Telephones

 provides procedures 

for installing Main Distribution Frames (MDF) and telephones. The procedures explain how you 
connect media gateways to the MDF and how to connect the MDF to the public switched 
telephone network (PSTN). This document also explains how to install and wire telephones.
The following information is included in this document:

●

Installing the main distribution frame

on page 13

●

Installing the patch panel

on page 29 

●

Media gateway connections to the MDF

on page 33

●

Installing and wiring telephones and trunks

on page 69

●

Testing the complete configuration

on page 135

Audience

This documentation is for the following audiences:

●

Trained field installation

●

Technical support personnel

●

Authorized Business Partners

How to use this documentation 

Use this documentation as a guide to install and connect MDFs and telephones. For information 
about a particular task, use the index or table of contents to locate the page number where the 
information is described.
Perform tasks related to the Main Distribution Frame in the following sections as appropriate:

●

Installing the main distribution frame

on page 13

●

Installing the patch panel

on page 29. This chapter is only for customers using a patch 

panel rather than a main distribution frame (typically smaller installations).

●

Media gateway connections to the MDF

on page 33

●

MDF connections to stations and the public switched telephone network

on page 41

Содержание 03-300686





























































































































































Отзывы:

Нет отзывов