manualshive.com logo in svg

Avaya 03-300686, Установка и подключение, Страница: 129 / 156

Поделиться
Скачать
Avaya 03-300686 Скачать руководство пользователя страница 129

C360 converged stackable switches

Issue 3 January 2008

129

 

●

Do not allow anything to rest on the power cord. Do not locate this product where the cord 
will be abused by persons walking on it.

●

Do not overload wall outlets and extension cords as this can result in the risk of line or 
electric shock.

●

Disconnect the cords on this product and refer servicing to qualified service personnel 
under the following conditions:

●

If the power supply cord or plug is damaged or frayed.

●

If liquid has been spilled into it.

●

If it has been exposed to rain or water.

●

If it was dropped or the housing has been damaged.

●

If it exhibits a distinct change in performance.

●

If it does not operate normally when following the operating instructions.

Using the C360 switch

The C360 Stackable Switch can be used to power 46xx series IP telephones in addition to 
providing a 10/100 megabits per second Ethernet connection. The switch can form part of a 
stack with the G700 Media Gateway or members of the P330 stackable switching system.

A C360 stack can contain up to 10 switches and up to three backup power supply units. The 
stacked switches connect using the stacking submodules that plug into a slot in the back of the 
C360. The X330RC cable connects the top and bottom switches in the stack and provides 
redundancy and hot-switchability. This characteristic is similar to how modules can be swapped 
in a modular switching chassis.

Avaya C360 switches are multilayer switches and can be upgraded with a license to provide 
routing (Layer3) functionality.

The C360 switches can be mounted in a standard 19-inch (48-centimeter) rack or mounted on a 
wall.

Содержание 03-300686





























































































































































Отзывы:

Нет отзывов