manualshive.com logo in svg

Avaya 03-300686, Установка и подключение, Страница: 148 / 156

Поделиться
Скачать
Avaya 03-300686 Скачать руководство пользователя страница 148

Testing the complete configuration

148 Installing and Connecting the MDF and Telephones

 

Telephone console LEDs

Telephones and attendant consoles have some alarm LEDs that must be checked out.

Attendant console LEDs 

The console has two red 

LED

s, labeled “ALM” and “ACK”. The ALM LED lights steadily when 

there is a major or minor alarm at the server. The ACK LED lights steadily if the alarm has been 
successfully reported to 

INADS

. If the server is unable to report the alarm to 

INADS

, the 

LED

 

flashes; this signals the attendant to call 

INADS

 and report the alarm.

Terminal alarm notification 

Terminal Alarm Notification is an optional feature that displays several types of alarms on 
telephones with administered feature buttons or the attendant console. A maximum of 10 digital 
and/or hybrid telephones may be used.
When an alarm occurs, the green status 

LED

 associated with the assigned button is in a steady 

state. The LED may be turned off by pressing the button associated with the LED. If the LED is 
off and the alarm has not been resolved by the time maintenance reschedules testing, the green 
status 

LED

 resumes its steady state. 

DS1 Converter circuit pack LEDs 

Eleven 

LED

s provide an indication of the state of the 

Figure 67: TN1654 DS1 Converter circuit 

pack LEDs

 and the T1/E1

 

facilities. The top group has the standard red, green and yellow 

LEDs. The red LED indicates an alarm condition and the green LED indicates testing in 
progress. The four SPAN LEDs indicate the status of the T1/E1 facilities. The four STATUS 
LEDs currently are unused and remain off. 

Содержание 03-300686





























































































































































Отзывы:

Нет отзывов