manualshive.com logo in svg

Avaya 03-300686, Установка и подключение, Страница: 135 / 156

Поделиться
Скачать
Avaya 03-300686 Скачать руководство пользователя страница 135

Issue 3 January 2008

135

 

Chapter 8: Testing the complete configuration 

This section provides tests for the complete configuration, including the control and signaling 
networks and the telephones and consoles. 
This section provides tests to:

●

review the status of the configuration.

●

test the duplication link to the servers (S8700-series only)

●

test the IP server interfaces, expansion interfaces, and TDM buses in the port networks.

●

test the telephones and other equipment.

See 

LED indicators

on page 147 for information regarding the LED status indicators for the 

Avaya Ethernet switch(es), uninterruptible power supplies (UPSs), and different circuit packs.

Note:

Note:

Circuit pack positions are usually given by cabinet, and slot. They may also be 
given by port. The term “cabinet” refers to five G650 Media Gateways 
TDM-cabled together in a rack, making up one port network. A port network is 
defined as a group of media gateways connected together with one TDM bus.

Perform these tasks to test the configuration:

!

CAUTION:

CAUTION:

To prevent unnecessary trouble tickets, do not enable the alarms (Alarm 
Origination feature) until all installation and administration procedures are 
completed.

1.

Testing port network equipment

on page 136

2.

Checking port network status for each media gateway

on page 136

3.

Checking circuit pack configuration

on page 137

4.

Testing the TN2312BP Internet Protocol Server Interface circuit pack

on page 138

5.

Testing Expansion Interface circuit packs, if used

on page 139

6.

Testing time division multiplexing bus for each port network

on page 140

7.

Testing expansion interface exchange, if used, for each port network

on page 141

8.

Testing telephones and other equipment

on page 142

Содержание 03-300686





























































































































































Отзывы:

Нет отзывов