Avaya 03-300686 Скачать руководство пользователя страница 22

Страница: 22 / 156

Installing the main distribution frame

22 Installing and Connecting the MDF and Telephones

11. If installing another distribution field terminal block, partially install the first screw for the

terminal block, on the line, 7/8-inch (2.2 centimeter) to the right of the previous screw.
Partially install the second mounting screw 7-11/16 inch (19.5 centimeter) to right of the
screw just installed. Repeat Steps 4, 5, and 6.

12. If installing a vertical patch cord trough in the distribution field, repeat Step 6.

13. Repeat Steps 11 and 12 until all the terminal blocks and vertical patch cord troughs in the

distribution field are installed.

Figure 5: 110A-type terminal blocks (300-pair)

Figure notes:

1. 4 feet (1.22 meters)
2. 6.6 feet (2 meters)
3. 7.68 inches (19.5 centimeters)
4. 7/8-inch (2.22 centimeters)
5. 5.31 inches (13.5 centimeters)

6. 47.5 inches (120.6

centimeters)

7. Horizontal Line
8. AC Power Strip
9. Floor Line

r758420b MMR 031496

Содержание 03-300686





























































































































































Результаты поиска

Содержание 03-300686

Отзывы:

Avaya 03-300686, Установка и подключение, Страница: 22 / 156

Результаты поиска

Содержание 03-300686

Отзывы: