manualshive.com logo in svg

Avaya 03-300686, Установка и подключение, Страница: 39 / 156

Поделиться
Скачать
Avaya 03-300686 Скачать руководство пользователя страница 39

Installing connector cables between auxiliary cabinet and MDF

Issue 3 January 2008

39

 

Installing connector cables between auxiliary cabinet and 
MDF 

Auxiliary equipment that connects to the MDF can be mounted inside the auxiliary cabinet. The 
equipment connects to an ED-1E1443-10 (Group 1) intraconnection panel mounted in the 
cabinet. This intraconnection panel consists of a 110-type 100-pair wiring block. Auxiliary 
equipment is connected to the 110-type wiring block. The wiring block is pre-wired to four 
25-pair female connectors mounted on the outside rear of the cabinet.

To install connector cables between the auxiliary cabinet and the main distribution frame:

1. Install “D” rings on the wall between the cable slack manager and the terminal/connecting 

blocks mounted on the MDF.

2. Install a self-sticking port label on the rear of each connector on the B25A connector cable. 

See 

Figure 16: Self-stick label on 25-pair cable connector

on page 39.

3. Labels should be positioned so the cabinet connector retainers do not obscure them.

4. At the rear of the auxiliary cabinet, connect 1 end of the connector cable to the assigned 

connector.

5. Route the cable down the rear of the cabinet and through the cable slack manager to the 

MDF.

6. At the MDF, connect the other end of the cable to the assigned terminal/connecting block 

connector.

7. Store the excess cable in the cable slack manager.

8. Repeat Steps 2 through 6 until all cables are installed.

Figure 16: Self-stick label on 25-pair cable connector

Содержание 03-300686





























































































































































Отзывы:

Нет отзывов