Avaya 03-300686 Скачать руководство пользователя страница 80

Страница: 80 / 156

Installing and wiring telephones and trunks

80 Installing and Connecting the MDF and Telephones

Table 9: DS1 cables

Connector cable

Description and usage

C6C connector cable

50-feet (15 meters) shielded cable equipped with a 50-pin

male connector on one end and a 15-pin male connector

on the other end.
Use this cable to connect a DS1 tie trunk circuit pack to a

CSU.

C6D connector cable

50-feet (15 meters) shielded cable equipped with a 50-pin

male connector on each end.
Use this cable to connect a DS1 tie trunks in collocated

cabinets.

C6E connector cable

100-feet (31 meters) shielded cable equipped with a

50-pin male connector on one end and a 50-pin female

connector on the other end.
Use this cable as an “extension” cable between the DS1

tie trunk circuit pack and other connector cables.

C6F connector cable

50-feet (15 meters) shielded cable equipped with a 50-pin

male connector on one end and a 3 inch (8 centimeter)

stub on the other end.
Use this cable to connect the DS1 tie trunk circuit pack to

channel multiplexers requiring hardwired connections.

Table 10: Pinout of C6F cable

Wire color

Lead
designation

Pin
number

White/Green

* (High Side)

Green

White/Brown

Brown

LO* (High Side)

White/Slate

LBACK2

Slate

LBACK1

Содержание 03-300686





























































































































































Результаты поиска

Содержание 03-300686

Отзывы:

Avaya 03-300686, Установка и подключение, Страница: 80 / 156

Результаты поиска

Содержание 03-300686

Отзывы: