Avaya 03-300686 Скачать руководство пользователя страница 131

Страница: 131 / 156

1151B1 and 1151B2 Power Supplies

Issue 3 January 2008

131

Connecting the cables

To connect IP telephones, PCs, servers, routers, workstations, and hubs.

1. Connect the Ethernet connection cable (not supplied) to a 10/100 megabits per second port

on the front panel of the Avaya C360 series switch.

Note:

Note:

Use standard RJ45 connections and a CAT5 cable for 100 megabits per second
operation.

2. Connect the other end of the cable to the Ethernet port of the PC, server, router,

workstation, IP telephone, switch, or hub.

3. Check that the appropriate link (LNK) LEDs light up.

1151B1 and 1151B2 Power Supplies

The 1151B1 and 1151B2 power supplies are a local power supply. The telephones or consoles
connect directly to them through an RJ45 connector. The 1151B2 has a battery backup.
These power supplies comply with the

Underwriters Laboratories Inc. (UL)

Standard UL

60950 third edition.

For safety instructions, see

Important safety instructions for 1151B1 and 1151B2 Power

Supplies

on page 132. For installation instructions, see

Connecting the 1151B1 or 1151B2

Power Supplies

on page 133.

Complies

UL 60950

Certified

CSA

C22.2

Approved

CE Regulatory Compliance

Содержание 03-300686





























































































































































Результаты поиска

Содержание 03-300686

Отзывы:

Avaya 03-300686, Установка и подключение, Страница: 131 / 156

Результаты поиска

Содержание 03-300686

Отзывы: