Avaya 03-300686 Скачать руководство пользователя страница 65

Страница: 65 / 156

Installing and administering the patch cord/jumper

Issue 3 January 2008

Connecting expansion control carrier outputs
cable (MCC1 Media Gateway only)

To connect the expansion control carrier outputs cable:

1. Plug the connector cable in the

AUX

connector on the rear of the expansion control carrier.

2. Route the connector cable through the cable slack manager to the assigned 110-type

terminal block in the yellow field of the trunk/auxiliary field.

Connecting trunk pairs using concentrator cables

Figure 31: Connect trunk pairs using concentrator cables

on page 66 shows trunk pairs

connected to the media gateway with concentrator cables. To install the cables:

1. Connect B25A cables between the network interface and sneak fuse panels.

2. Connect A25D cables from the sneak fuse panels to the 110-type terminal block connectors

in the green field.

3. Connect patch cords/jumper wires from the terminal block in the green field to the

associated terminal block in the purple field.

4. Connect the single-fingered end of the concentrator cables to the 110-type terminal block

connectors in the purple field in Step 3.

5. Connect the other end (2/3-fingered end) of the concentrator cables to the appropriate

carrier slots. Equipped carrier slots are identified on the CSD. Mark the nomenclature strips
above the carriers to identify the slots.

6. Label connectors on each end of the cables that connect to the media gateway.

7. Route the cables down the sides of the media gateway and store the excess cable slack in

the cable slack manager as previously described.

Содержание 03-300686





























































































































































Результаты поиска

Содержание 03-300686

Отзывы:

Avaya 03-300686, Установка и подключение, Страница: 65 / 156

Результаты поиска

Содержание 03-300686

Отзывы: