Asyril Asycube Control URCap Скачать руководство пользователя страница 12

Страница: 12 / 50

Asycube Control URCap

User guide

Asycube Control URCap installation and configuration

Version: A2

000.102.083

12/50

Figure 2-7

– Connection management with the Asycube platform

Through the

Network

sub-menu, the user can specify the network settings of the Asycube

platform: IP address, subnet mask and port. These settings must be same as the ones

specified with the HMI software (2.3.1 Asycube network settings).

Once the right network settings are specified, the user can connect to the platform by clicking

on the button

Connect

, and disconnect it by clicking on the button

Disconnect

. At the bottom

of the interface, a message is displayed to specify the current state of the

connection/disconnection process. If an error occurs during the connection or the

disconnection process, a popup will be displayed, specifying the reason of the error. The

platform unit, once connected, is displayed at the

Unit

dropdown level.

By clicking on the

Auto connect

checkbox, the user specifies that the platform must be

automatically connected when the robot is started.

At the bottom of the main menu of the URCap, at the

Installation

tab level, and in the Network

sub-menu, a visual indicator is displayed and gives the current connection status of the

Asycube platform at any time (green if connected; red if not).

If a disconnection occurred when handling the URCap, the user must go back to the

Network

sub-menu to reinitialize the connection with the Asycube.

Содержание Asycube Control URCap



















































Результаты поиска

Содержание Asycube Control URCap

Отзывы:

Похожие инструкции для Asycube Control URCap

Бренды по названию

Популярные бренды

Asyril Asycube Control URCap, Руководство пользователя

Результаты поиска

Содержание Asycube Control URCap

Отзывы:

Похожие инструкции для Asycube Control URCap

Бренды по названию

Популярные бренды